- 3cx 11 spa password#
- 3cx 11 spa Pc#
The time servers indicated in the picture below:
Set your Primary NTP Server to 0., or your preferred working NTP server. Make sure your DNS Server Order is set to Manual, DHCP. You can also set your Secondary DNS server to a Set your Primary DNS server to a public DNS server such as 208.67.222.222. Continue to Step 4.Ĭlick on WAN Setup and then make the following changes: We are now ready to enter your Callcentric account information as well as properly configure your time and DNS servers. First click on Admin login from the right side of the page, We now want advanced access to this device so that we may make the proper configuration changes. Once logged in you should see a page such as the following: 3cx 11 spa password#
If you are prompted for a username and password please enter the one you configured. For example if you heard "192.168.001.010" you should change this to "192.168.1.10"īy default the SPA3102 does not have an username/password associated with it. Please note: You do not need to enter the leading zero's ( 0 's ) in the IP address.
Now that you have your device's IP address simply open your favorite web browser and enter the IP address in the address bar and press enter. Once you have acquired your device's IP continue on to Step 2 below.
3cx 11 spa Pc#
If your computer is not connected to the yellow port on the back of the SPA3102 then please do the following:Įlse if your PC is connected to the yellow port on the back or your SPA3102 then the SPA3102 IP should be 192.168.0.1, unless you changed the subnet in your advanced configuration. If you have already enabled web configuration you simply need to acquire your device's IP address in order to configure it. You should now have the IP address for your SPA3102 as well as the ability to configure your device through your web browser. You will hear the menu prompt again after acquiring the IP address.Īfter hearing the prompt dial 7932# followed by 1# then 1 when asked to save the change. as now you will need to enable web-based configuration, since by default the web-based configuration for the WAN port is disabled. Write this number downĭo not hang up yet.
You will now hear a message giving you the IP address of your PAP2 such as - " 192.168.001.100". Please enter option followed by the pound key.", then enter 1 1 0 # on your phone. You will hear a message - " Linksys configuration menu. 
Dial ****, do this even if you hear a busy signal. Pen and paper ready to write down the IP address. If this is your first time configuring your SPA3102 then you will need to first find the IP address of your device and then enable HTTP configuration. We recommend that you read each step through in its entirety before performing the action indicated in the step. Once you have verified this please continue configuring your device with the instructions below. You will also want to connect a regular telephone (RJ11) cable to the phone port labeled "Phone". The configuration information below is based on firmware version 5.1.7(GW), which is the latest version as of this writing.īefore we proceed please make sure that your SPA3102 is powered on and that you have an ethernet (RJ45) cable connected with one end to your router/modem/gateway and the other end to the blue port on the back of the SPA3102. The SPA3102 is reliable and relatively inexpensive and can be considered by individuals who want the extra PSTN functionality for their specific environments. In addition to the similar appearance the SPA3102 also adds extra features not present in the PAP2/T such as an FXO (Foreign Exchange Office: allowing you to use a normal PSTN line or PBX line for redundancy in case of an outage on your ISP.etc) and a built in router allowing you to share your internet without the need for a standard router/switch. The SPA3102 is a Linksys device, similar to the PAP2/T line of devices in appearance and configuration. Security considerations for Callcentric customersĭID-Based Routing with trixbox / Asterisk Admin GUI / Elastix / PBX-in-a-Flash
0 kommentar(er)
